ip link add name br0 type bridge
ip link set dev br0 up
ip link set dev eth0 master br0
ip link set dev eth1 master br0

ip link set dev eth0 nomaster

ip link del br0

Для управления бриджем FDB(Forwarding Database) используем команду bridge(8).

Примеры:

bridge fdb show dev br0

bridge link set dev eth0 guard on

bridge link set dev eth1 cost 4

bridge link set dev eth1 root_block on

Cost is calculated using some factors, and the link speed is one of them. Using a fix cost and disabling the processing of BPDUs and enabling root_block is somehow simmilar to a guard-root feature from switches.

Другие расширения типа: vepa, veb и hairpin режимов могут быть найдены на соответвствующей странице команды bridge.

ip link add link eth0 name eth0.2 type vlan id 2
ip link set eth0.2 up

ip link set eth0.2 down
ip link del eth0.2

Подробности читаем тут.

modprobe bonding

ip link add bond0 type bond
echo 4 > /sys/class/net/bond0/bonding/mode
ip link set eth0 master bond0
ip link set eth1 master bond0
ip link set bond0 up

<spoiler | режимы в /sys/class/net/bond0/bonding/mode >

Specifies one of the bonding policies. The default is
balance-rr (round robin).  Possible values are:

	balance-rr or 0
		Round-robin policy: Transmit packets in sequential
		order from the first available slave through the
		last.  This mode provides load balancing and fault
		tolerance.

	active-backup or 1
		Active-backup policy: Only one slave in the bond is
		active.  A different slave becomes active if, and only
		if, the active slave fails.  The bond's MAC address is
		externally visible on only one port (network adapter)
		to avoid confusing the switch.

		In bonding version 2.6.2 or later, when a failover
		occurs in active-backup mode, bonding will issue one
		or more gratuitous ARPs on the newly active slave.
		One gratuitous ARP is issued for the bonding master
		interface and each VLAN interfaces configured above
		it, provided that the interface has at least one IP
		address configured.  Gratuitous ARPs issued for VLAN
		interfaces are tagged with the appropriate VLAN id.

		This mode provides fault tolerance.  The primary
		option, documented below, affects the behavior of this
		mode.

	balance-xor or 2
		XOR policy: Transmit based on the selected transmit
		hash policy.  The default policy is a simple [(source
		MAC address XOR'd with destination MAC address XOR
		packet type ID) modulo slave count].  Alternate transmit
		policies may be	selected via the xmit_hash_policy option,
		described below.
		This mode provides load balancing and fault tolerance.

	broadcast or 3
		Broadcast policy: transmits everything on all slave
		interfaces.  This mode provides fault tolerance.

	802.3ad or 4
		IEEE 802.3ad Dynamic link aggregation.  Creates
		aggregation groups that share the same speed and
		duplex settings.  Utilizes all slaves in the active
		aggregator according to the 802.3ad specification.

		Slave selection for outgoing traffic is done according
		to the transmit hash policy, which may be changed from
		the default simple XOR policy via the xmit_hash_policy
		option, documented below.  Note that not all transmit
		policies may be 802.3ad compliant, particularly in
		regards to the packet mis-ordering requirements of
		section 43.2.4 of the 802.3ad standard.  Differing
		peer implementations will have varying tolerances for
		noncompliance.
		Prerequisites:
		1. Ethtool support in the base drivers for retrieving
		the speed and duplex of each slave.
		2. A switch that supports IEEE 802.3ad Dynamic link
		aggregation.
		Most switches will require some type of configuration
		to enable 802.3ad mode.

	balance-tlb or 5
		Adaptive transmit load balancing: channel bonding that
		does not require any special switch support.

		In tlb_dynamic_lb=1 mode; the outgoing traffic is
		distributed according to the current load (computed
		relative to the speed) on each slave.

		In tlb_dynamic_lb=0 mode; the load balancing based on
		current load is disabled and the load is distributed
		only using the hash distribution.

		Incoming traffic is received by the current slave.
		If the receiving slave fails, another slave takes over
		the MAC address of the failed receiving slave.

		Prerequisite:

		Ethtool support in the base drivers for retrieving the
		speed of each slave.

	balance-alb or 6
		Adaptive load balancing: includes balance-tlb plus
		receive load balancing (rlb) for IPV4 traffic, and
		does not require any special switch support.  The
		receive load balancing is achieved by ARP negotiation.
		The bonding driver intercepts the ARP Replies sent by
		the local system on their way out and overwrites the
		source hardware address with the unique hardware
		address of one of the slaves in the bond such that
		different peers use different hardware addresses for
		the server.

		Receive traffic from connections created by the server
		is also balanced.  When the local system sends an ARP
		Request the bonding driver copies and saves the peer's
		IP information from the ARP packet.  When the ARP
		Reply arrives from the peer, its hardware address is
		retrieved and the bonding driver initiates an ARP
		reply to this peer assigning it to one of the slaves
		in the bond.  A problematic outcome of using ARP
		negotiation for balancing is that each time that an
		ARP request is broadcast it uses the hardware address
		of the bond.  Hence, peers learn the hardware address
		of the bond and the balancing of receive traffic
		collapses to the current slave.  This is handled by
		sending updates (ARP Replies) to all the peers with
		their individually assigned hardware address such that
		the traffic is redistributed.  Receive traffic is also
		redistributed when a new slave is added to the bond
		and when an inactive slave is re-activated.  The
		receive load is distributed sequentially (round robin)
		among the group of highest speed slaves in the bond.

		When a link is reconnected or a new slave joins the
		bond the receive traffic is redistributed among all
		active slaves in the bond by initiating ARP Replies
		with the selected MAC address to each of the
		clients. The updelay parameter (detailed below) must
		be set to a value equal or greater than the switch's
		forwarding delay so that the ARP Replies sent to the
		peers will not be blocked by the switch.

		Prerequisites:
		1. Ethtool support in the base drivers for retrieving
		the speed of each slave.
		2. Base driver support for setting the hardware
		address of a device while it is open.  This is
		required so that there will always be one slave in the
		team using the bond hardware address (the
		curr_active_slave) while having a unique hardware
		address for each slave in the bond.  If the
		curr_active_slave fails its hardware address is
		swapped with the new curr_active_slave that was
		chosen.

</spoiler>

ip link set bond0 down
ip link del bond0

bridge vlan show

bridge vlan add dev eth1 <vid, pvid, untagged, self, master>

bridge vlan delete dev eth1 <vid, pvid, untagged, self, master>